99精品视频免费热播在线观看丨无码国产成人午夜视频在线播放丨97碰碰碰免费公开在线视频丨成a人片亚洲日本久久丨欧洲精品卡1区2卡三卡四卡

Welcome to Hashimoto Precision Metal (Shenzhen) Ltd

Mailbox:

info@hskcoltd.com

Hashimoto Precision Metal (Shenzhen) Ltd

Specialize in precision stamping parts since 1935
News
Your position: Home > News > Industry news > Common failures of automobile terminals

Contact us

Hashimoto Precision Metal (Shenzhen) Ltd

Address: No. 25, Xinfa East Road, Xiangshan Community, Xinqiao street, Bao'an District, Shenzhen 518125, P.R.China

Tel: +86-755-27267875

Email: info@hskcoltd.com

Industry news

Common failures of automobile terminals
Release time:2021-12-16Views:5319


The conductivity of plastic insulation materials and automobile terminal is the key factor affecting the quality of automobile terminals. They determine the insulation and conductivity of automobile terminals respectively. The failure of any connection end will lead to the failure of the entire system engineering. Needless to say, there are many warning cases. As a precision operation accessory, the quality of motion control terminal has always been a concern of users. How to effectively detect and prevent has become a topic of concern.


Common failures of automobile terminals


From the perspective of use, the function of automobile terminal is: the contact point shall be connected, the contact point must be energized and the contact shall be reliable. The insulation must be reliable. There are three common fatal faults at line terminals


1. Poor exposure.

The metal conductor within the terminal is a core component. It transmits voltage, current or signals from the external wire or cable to the corresponding contact, which is the connector. Therefore, the contact point must have excellent structure, stable and reliable contact retention force and good electrical conductivity. Unreasonable contactor structure design, improper selection of materials, poor die stability, out of tolerance processing size, rough surface, unreasonable heat treatment coating and other surface treatment processes, poor storage and use environment and improper operation will lead to poor contact between contact parts and coordination parts


2. Poor thermal insulation performance.

The function of insulator is to keep the contact in the correct position and insulate between contact and contact, contact and shell. Therefore, the insulator must have good electrical, mechanical and process forming performance. Especially, due to the wide application of high density and small size connectors, the effective wall thickness of insulator is also getting thinner and thinner. More stringent requirements are put forward for insulation materials, injection mold accuracy and molding process. Because there are metal residues, surface dust, welder agent and other pollution on the surface or inside of the insulator, the precipitation of organic matter and the fusion of harmful gas adsorption film and surface water film form ion conduction channel, moisture absorption, mildew, insulation material aging, etc., which may cause short circuit, power leakage, breakdown, low insulation resistance and poor insulation.

3. No-fixed-position issue

The thermal insulation material not only provides insulation effects, but also usually provides accurate neutralization protection for extended contacts. At the same time, it also has the function of installing positioning and locking devices.

If the installation is not good, it will affect the contact and cause instantaneous power failure, and the product will disintegrate in serious cases. Disassembly refers to abnormal separation between plug and jack, due to unreliable structure caused by materials, design, process etc when the connector is plugged in, which will seriously affect the power transmission and signal control interruption of the control system. Poor installation is caused by unreliable design, improper selection of materials, improper selection of forming process, poor process quality such as heat treatment, mold, assembly and welding, and inadequate assembly.


In addition, poor appearance caused by coating peeling, corrosion, collision, plastic shell flash, fracture, rough processing and deformation of contact parts, and poor shaping caused by poor positioning size, poor processing quality, excessive total separation force etc. These faults can generally be found and eliminated in time during inspection and use.



How to check the terminal short circuit fault?

Failure of lead and terminal may also be caused by a short circuit between the harness and the body (ground wire) or within the relevant switch. First check whether the automobile terminal is firm, and then carry out the test according to the following steps

1. Check the connection of the wires.

First remove the control terminals on both sides of the control computer ECU and the sensor, and then measure the resistance between the corresponding terminals. If the resistance does not exceed 1 ohm, the power line is normal for the next inspection. When testing the conductor resistance, it is best to gently shake the conductor in the vertical and horizontal directions to improve the measurement accuracy. Multiple wire terminals shall be inserted with multi-meter bars from the back end of the connector. However, the waterproof automobile terminal rod cannot be inserted from the rear end, because the terminal will be deformed if it is accidentally inserted.

2. Detect the short-circuit resistance value

First disassemble the ECU of the control computer and the wires automobile terminals on both sides of the sensor, and then measure the resistance value between the connectors and the body. During the measurement, one end of the meter bar is connected with the iron body, and the other end shall be measured respectively on the two wire connectors. If the resistance value is greater than 1Ω, it indicates that there is no short circuit fault.

3. Terminal appearance and contact pressure inspection.

First disassemble each terminal one by one and check whether there is rust and dirt on the automobile terminal. Then check whether the junction box is loose and damaged, whether the junction box is firm. Make sure the junction box is not loose after light pulling. Conversely, if it is easier to pull out the plug end, the socket may cause failure with poor contact during use.

Inquire Now * required
Submit
主站蜘蛛池模板: 久久无码精品一一区二区三区| 亚洲成a人片在线观看天堂无码| 亚洲国产精品久久久久爰色欲| 无码专区天天躁天天躁在线| 欧美激情视频一区二区三区免费 | 国产综合视频一区二区三区| 亚洲第一无码av无码专区| 黑人大群体交免费视频| 日本熟妇大乳| 欧美另类videosbestsex日本| 国产成人欧美一区二区三区| 成视频年人黄网站免费视频| 国产寡妇婬乱a毛片视频| 欧美xxxxx高潮喷水| 亚洲精品蜜夜内射| 人人妻人人爽人人澡人人| 国产高清乱码女大生av| 在厨房被c到高潮a毛片奶水| 精品国产人妻一区二区三区免费| 波多野无码中文字幕av专区| 国产av天堂亚洲国产av天堂 | 久久国产精品娇妻素人| 男女啪啦啦超猛烈动态图| 他掀开裙子把舌头伸进去添视频| 亚洲欧美另类激情综合区| 日本一区二区三区免费播放视频站| 未满十八勿入av网免费| 真人一进一出120秒试看| 日本一区二区在线高清观看| 国产亚洲精品麻豆一区二区| 久久国产乱子伦精品免费午夜| 精品国产在天天线2019| 宅男66lu国产在线观看| 成人精品av一区二区三区网站| 亚洲精品无码人妻无码| 老熟妇乱子伦牲交视频欧美| 香港三级日本三级韩级人妇| 视频一区国产第一页| 欧美三級片黃色三級片黃色 | 久久精品国产99国产精品图片| 国产精品美女久久久久久丫|